Добро пожаловать
Вход

நம் வீட்டில் Water Level Indicator மற்றும் Alarm செய்வது எப்படி | How to Make DIY Water Level Alarm

Спасибо! Поделитесь с друзьями!

URL

Вам не понравилось видео. Спасибо за то что поделились своим мнением!

К сожалению, только зарегистрированные пользователи могут создавать списки воспроизведения.
URL


Добавлено от Admin В Автомобильные товары
10 Просмотры

Описание

நம் வீட்டில் Water Level Indicator மற்றும் Full Alarm செய்வது எப்படி | How to Make DIY Water Level indicator with Alarm in home

Buy Full Kit Here : https://imojo.in/4bh5swu - Rs.589
Needed Things Mension Below ---
----------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------------
#1 9V Battery With Connector(5 Pieces link)
https://amzn.to/2KezZLV

#2 220 ohm resistor(set of 100 Pieces link)
https://amzn.to/2LXj0j6

#3 BC547 Transistor (set of 10 Pieces)
https://amzn.to/2LXwVWy

#4 LED Lights 5 Different Colours (set of 100 Pieces)
https://amzn.to/2ZtB0EX

#5 Switch (set of 20 Pieces)
https://amzn.to/2GJCUKi

#6 Sound Buzzer(2 Pieces)
https://amzn.to/2ZupxEX

#7 Diy Project Wire Black Colour(5 meters)
https://amzn.to/31arruY


#SaveWater #Top10Tamil
Today I am going to talk about a very useful project that I had taken up. It is called the Water Level Indicator. Nowadays everybody has overhead tank at their homes. But everyone who has a water tank above knows the kind of problems that they face. Firstly there is no system to track the water in the tank. Then there come a secondary problem that is when their water pump is started they have no idea when it gets filled up and sometimes there are situation where the pump keeps on pumping water to the tank and the water starts spilling out from the tank. There is wastage of energy as well as wastage of water.

The house where I live in has an overhead tank which is about 30 feet from the ground level. I was getting bored going up the rooftop to check whether the tank has filled or the water level was below to start the pump. I had to do this again and again. Then I sought for a solution. I always used to think of the possibilities of how can this problem be tackled in an electronic way. After years of research and by trial and error, I found one and wanted to put whatever I have done out here so that it may be helpful to someone who has a overhead water tank at their homes.

Basically the unit is made up of various sensors acting as a switch. Let me explain in a simple way. What happens is when you turn on you water pump, the water starts to get pumped from your underground reservoir or from your underground water supply from the pipes to your water tank. In the tank there is a set of sensors, in the water tank. Just think them as a switch, as the work of the sensor will be to connect a circuit. So the water starts to get filled in the tank and when the water level in the tank starts to rise up, what happens is that the sensors that is installed in the tank starts to get activated one by one indicating the water level in the tank. And finally when it reaches to its top most sensor, there will be a visual display as well as a sound from the unit indicating that the water has filled in the tank and one can be alerted that the tank has been filled up and the water pump has to be switched off saving the electricity bill as well as over flow of water from the tank.

The heart of the circuit is the transistors BC 547. There are total 5 transistors in the circuit and each one will be sensing the level of water present in the overhead water tank. There is one extra power LED without a transistor and that is because this Red LED will be telling us two things. Firstly when you power the unit it will be monitoring the power present in the unit and secondly it is also the indicator telling you that there is no water at all present in the tank. As because the water level is below the No. 1 (as shown in the circuit) sensor, no LED's will be lighting up, but only for the one Red LED. Therefore when you switch on your unit if you see only one Red LED lighting up then you know that the is no water present in the tank and therefore you should make you water pump on.
Then as shown in the figure i have given all the LED's in various color.

Here you can add any of the normal buzzers that are readily available in the market and if it is not then you can make yourself with a simple . I am giving a small circuit diagram, it is really simple to make and there are minimum parts. It is a simple audio oscillator. I have also provide a circuit diagram here but if you are able to manage a buzzer then no need to assemble this circuit.

Написать комментарий

Комментарии

Комментариев нет.
RSS
Добро пожаловать на наш сайт. Здесь Вы сможете посмотреть огромное количество видео-отзывов о товарах, которые пользователи приобретали в сети интернет в соответствующих интернет-магазинах. Наш сайт не осуществляет какие-либо реализации товаров или услуг, а служит ресурсом ознакомительного характера для возможности принять решение о приобретении товаров, ранее купленных пользователями сети интернет. Также уведомляем правообладателей каких-либо товарных знаков о том, что сайт не загружает и распространяет какие-либо видео, контент, нарушающий исключительные права владельцов товарных знаков. Все ссылки на видео взяты из открытого источника по API информационного ресурса youtube.com. Если у Вас остались вопросы по поводу функционирования сайта или Вы хотите, чтобы Ваш бренд был освещен на нашем сайте в качестве дополнительной рекламы, при этом на каналах youtube достаточно много пользовательских видео-отзывов о Вашем бренде, напишите нам через форму обратной связи и мы с удовольствием добавим информационные материалы на сайт с целью продвижения Вашего товарного знака и для возможности получения информации нашим пользователям о Вашем товаре.
Яндекс.Метрика